{glow - fotoluminescencyjny
Numer artykułu PS111XA11}
HEWI System 111 panic bar
to equip emergency exit doors - Approval according to EN 1125 for single or double doorsets in escape routes, stainless steel, Satin surface, diameter 25 mm with tubular handle made of polyamide diameter 30 mm, 20 mm wide luminescent rings on the two outer sides for orientation in case of light failure, conforms to the requirements of DIN 18040, Low projection in accordance with EN 1125, classification 2: <= 100 mm, width of the rose 27.7 mm, width of the gear unit 45 mm.
Information on the classification of the panic bar according to DIN EN 1125 can be found in the certificates of the respective lock manufacturer.
Recommendation! Please check all dimensions and constructional conditions in case of order!
Pokaż więcej
to equip emergency exit doors - Approval according to EN 1125 for single or double doorsets in escape routes, stainless steel, Satin surface, diameter 25 mm with tubular handle made of polyamide diameter 30 mm, 20 mm wide luminescent rings on the two outer sides for orientation in case of light failure, conforms to the requirements of DIN 18040, Low projection in accordance with EN 1125, classification 2: <= 100 mm, width of the rose 27.7 mm, width of the gear unit 45 mm.
Information on the classification of the panic bar according to DIN EN 1125 can be found in the certificates of the respective lock manufacturer.
Recommendation! Please check all dimensions and constructional conditions in case of order!
Typ blokady
Wilka
Rurka z kolorowym uchwytem
DIN Kierunek
Prawo
EAN
4014885594956
Materiał ramy drzwi
Metal i aluminium
Odległość montażowa
861 - 1010 mm
Artikelnummer
PS111XA11
System 111 panic bar
for equipping exit doors - approval to EN 1125 only in combination with tested locks - with CE marking. Approved for fire and smoke doors, listing in the national technical approval test certificate of the respective door manufacturer in conjunction with DIN 18273, DIN 4102, DIN 1634, for single leaf or double doorsets in escape routes (inactive or inactive and active leaf)
Handle made of stainless steel, diameter 25 mm with tubular handle made of polyamide, diameter 30 mm. 20 mm wide luminescent rings on the two outer sides for orientation in case of light failure. Handle tube positioned as one-sided handle, therefore clear visualisation of the optimum pressure point on the lock side, conforms to the requirements of DIN 18040. The stainless steel tubes are connected by a square bar - telescopic. Low projection depending on the operating angle of the lock follower, but at least in accordance with DIN 1125, grade 2: <= 100 mm.
Mounting distance 761 - 860 mm, 861 - 1010 mm, 1011 - 1160 mm, 1161 - 1300 mm, 1301 - 1440 mm and 1441 - 1580 mm. Variable mounting distance: shorter bar (fixing centres > 761 mm) at customer request, specify exact measurement. For use on timber and steel doors and metal frame doors, backset from 35 mm (depending on profile) as single or double doorset. Concealed, tamper-resistant screw fixing with threaded screws M5. Gear unit and the thrust bearing with cover, width of the rosette 27.7 mm, width of the transmission unit 45 mm, no jamming due to splayed surfaces of the gear unit cover on the lock side and positioning of the push-bar on the inside of the gear unit. Surface satin finished.
Information on the classification of the panic bar according to EN 1125 can be found in the certificates of the respective lock manufacturer.
for equipping exit doors - approval to EN 1125 only in combination with tested locks - with CE marking. Approved for fire and smoke doors, listing in the national technical approval test certificate of the respective door manufacturer in conjunction with DIN 18273, DIN 4102, DIN 1634, for single leaf or double doorsets in escape routes (inactive or inactive and active leaf)
Handle made of stainless steel, diameter 25 mm with tubular handle made of polyamide, diameter 30 mm. 20 mm wide luminescent rings on the two outer sides for orientation in case of light failure. Handle tube positioned as one-sided handle, therefore clear visualisation of the optimum pressure point on the lock side, conforms to the requirements of DIN 18040. The stainless steel tubes are connected by a square bar - telescopic. Low projection depending on the operating angle of the lock follower, but at least in accordance with DIN 1125, grade 2: <= 100 mm.
Mounting distance 761 - 860 mm, 861 - 1010 mm, 1011 - 1160 mm, 1161 - 1300 mm, 1301 - 1440 mm and 1441 - 1580 mm. Variable mounting distance: shorter bar (fixing centres > 761 mm) at customer request, specify exact measurement. For use on timber and steel doors and metal frame doors, backset from 35 mm (depending on profile) as single or double doorset. Concealed, tamper-resistant screw fixing with threaded screws M5. Gear unit and the thrust bearing with cover, width of the rosette 27.7 mm, width of the transmission unit 45 mm, no jamming due to splayed surfaces of the gear unit cover on the lock side and positioning of the push-bar on the inside of the gear unit. Surface satin finished.
Information on the classification of the panic bar according to EN 1125 can be found in the certificates of the respective lock manufacturer.
Nagrody za wzornictwo
Przyznane przez
Drążek antypaniczny zgodny z EN 1125
{glow - fotoluminescencyjny
Numer artykułu PS111XA11}